ATF 5.50 New Loaders + New Box Firmware Update!!
First In the World to add Support for the Latest Nokia Flash Loader Pacakge 10.20.001.6 (May 18, 2010)
N86 RM-484 42 SEC
http://www.youtube.com/watch?v=cgX_b6ZheI0
5230 RM-588 38 SEC
http://www.youtube.com/watch?v=KM7eXw3d8vA
[New FPGA Firmware]
LogiCore 7.07.10
[BB5 Nitro Engine]
Now using the Lastest Flash Loader Pacakge 10.20.001.6
[BB5 Turbo Engine]
Now using a more stable RAP3gV2 and V3 Loaders
[DCT4 Engine]
Booting Problem Fixed for DCT4+ Phones
[General Fixes and Tweaks]
Quick Access "Backup RPL" Button is now on the Main Software Page
http://www.youtube.com/watch?v=mk0MvQbk7Hw
Who will buy this if you can get more in ATF?
Some Important Information...
1. Nitro Mode is Selected by default when the solftware loads. I personally suggest to use
Nitro Mode on all phones, since it will automatically swtich to Turbo Mode when the
software detects an unsupported phone.
2. Flashing with External VPP + 15 Mhz is not advisable UNLESS the phone is SL3.
External VPP + 7.5 Mhz is suggested for SL1 and SL2 phones if you have a VPP Enabled Cable.
3. FBUS Stalls/Hangs are still present... ;o( But let it finish it's job especially when
reading DCT4 PM.
4. You must Upgrade your Box Firmware to LogiCore 7.07.10. Modified Boxes and NON
Modified Boxes are both 100% Upgradable and Downgradable. So there is no difference
when it comes to the Support.
5. For POWER HUNGRY Phones like N95, N95-8GB, N97, E90 etc... If you are not using a
TMA during flashing and the flashing procedure "hanged", you need to flash again but
this time PRESS the POWER BUTTON of the phone before pressing the FLASH Button
and only let go of the power button when the software starts to erase the phone.
N86 RM-484 42 SEC
http://www.youtube.com/watch?v=cgX_b6ZheI0
5230 RM-588 38 SEC
http://www.youtube.com/watch?v=KM7eXw3d8vA
[New FPGA Firmware]
LogiCore 7.07.10
[BB5 Nitro Engine]
Now using the Lastest Flash Loader Pacakge 10.20.001.6
[BB5 Turbo Engine]
Now using a more stable RAP3gV2 and V3 Loaders
[DCT4 Engine]
Booting Problem Fixed for DCT4+ Phones
[General Fixes and Tweaks]
Quick Access "Backup RPL" Button is now on the Main Software Page
http://www.youtube.com/watch?v=mk0MvQbk7Hw
Who will buy this if you can get more in ATF?
Some Important Information...
1. Nitro Mode is Selected by default when the solftware loads. I personally suggest to use
Nitro Mode on all phones, since it will automatically swtich to Turbo Mode when the
software detects an unsupported phone.
2. Flashing with External VPP + 15 Mhz is not advisable UNLESS the phone is SL3.
External VPP + 7.5 Mhz is suggested for SL1 and SL2 phones if you have a VPP Enabled Cable.
3. FBUS Stalls/Hangs are still present... ;o( But let it finish it's job especially when
reading DCT4 PM.
4. You must Upgrade your Box Firmware to LogiCore 7.07.10. Modified Boxes and NON
Modified Boxes are both 100% Upgradable and Downgradable. So there is no difference
when it comes to the Support.
5. For POWER HUNGRY Phones like N95, N95-8GB, N97, E90 etc... If you are not using a
TMA during flashing and the flashing procedure "hanged", you need to flash again but
this time PRESS the POWER BUTTON of the phone before pressing the FLASH Button
and only let go of the power button when the software starts to erase the phone.
0 comments:
Post a Comment